Post by: A.O. on January 01, 2019, 08:06:45 AM
It has a set of anti kickback fingers that are on a rod on the feed end of the machine, these fingers are supposed to loosely pivot on the rod to be effective. On my machine they are very gummed up with something, pitch maybe? Anyway, I see no way to remove them to clean without a major disassembly of the machine! I do have the manual and it says nothing about them except to keep them clean!
Does anyone know how to get them out, or know of something I could spray them down with to loosten them up??
They are so gummed up its kinda hard to even start a board through the machine!
Thanks in advance!
Here's a PDF of the manual...
http://content.jettools.com/assets/manuals/708531_man_EN.pdf
Post by: Ox on January 01, 2019, 09:46:35 AM
Post by: A.O. on January 01, 2019, 10:15:38 AM
Best stuff I use regularly for any of that sort of thing is a mixture of ATF and kerosene, 50/50. I use used ATF from maintenance on vehicles until I run out of it, then I'm forced to use new stuff. But straight ATF by itself will cut through that gunk because of its high detergent properties. Or straight kero or diesel will cut through.
Thanks
So far I've used Gunscrubber, gum out choke cleaner, WD40, and WD40 silicone. Loosens them up a bit, but not enough.
I'll give it a try, dont have kerosene but I have diesel, and a couple varieties of ATF.. pretty close I'm thinking..
Post by: furu on January 01, 2019, 11:27:42 AM
Post by: Ox on January 02, 2019, 09:07:44 AM
The different ATFs available are close enough to one another for your purpose here it simply doesn't matter - use any old thing. But don't just use any old thing in a vehicle transmission! The different fluids have different friction modifiers (or something like that! lol) and can act differently in different transmissions.
Post by: A.O. on January 02, 2019, 09:41:40 AM
Post by: bandmiller2 on January 02, 2019, 04:55:56 PM
Post by: Ox on January 03, 2019, 09:52:16 AM
Post by: A.O. on January 03, 2019, 10:21:50 AM
Ox , you are correct!
I ended up removing the entire assembly to clean and inspect. Turns out it wasn't that gummed up, but slightly damaged. one of the fingers was bent pretty bad and a couple more were bent a little bit. So I flattened them back out with a mallet and an anvil. I put them in a tumbler to clean them all up for a couple hours, when that is done I'll re assemble the unit to check for functionality and if it works ok I'll re-disassemble and reinstall!
So these guys should be dead flat, obviously not the case!
(http://i255.photobucket.com/albums/hh136/hunt4570/South%20Carolina/SAWMILL/IMG_0153_zpsjtezic2x.jpg) (http://s255.photobucket.com/user/hunt4570/media/South%20Carolina/SAWMILL/IMG_0153_zpsjtezic2x.jpg.html)
(http://i255.photobucket.com/albums/hh136/hunt4570/South%20Carolina/SAWMILL/IMG_0152_zps7knampr0.jpg) (http://s255.photobucket.com/user/hunt4570/media/South%20Carolina/SAWMILL/IMG_0152_zps7knampr0.jpg.html)
So the bend in them made the assembly to wide to fit between the keepers on the ends and caused it to bind and not function correctly.
(I took a bunch of pictures on the procedure, If management would like I could document the procedure for future reference.)
Post by: Crusarius on January 03, 2019, 11:00:11 AM
Post by: A.O. on January 03, 2019, 11:05:46 AM
the holes are not to small are they?
?? Why / How would the holes be too small?
Post by: Crusarius on January 03, 2019, 11:58:37 AM
Post by: A.O. on January 03, 2019, 01:19:31 PM
Just curious if they were out of round or bent with the plate. could cause issues to
That's a possibility I guess, but I didn't have a problem in that regard. Just seems with them bent it made the whole assembly too wide.
These all hang from a round bar and have a keeper on each end to keep them in place. as soon as I removed those keepers taking it apart the fingers started hanging "loose" s they were supposed to do.
So now its all cleaned up and back together and works just as it should.!
Before shot of assembly..
(http://i255.photobucket.com/albums/hh136/hunt4570/South%20Carolina/SAWMILL/IMG_0143_zps0lcfjza2.jpg) (http://s255.photobucket.com/user/hunt4570/media/South%20Carolina/SAWMILL/IMG_0143_zps0lcfjza2.jpg.html)
Post by: furu on January 04, 2019, 07:06:15 AM
Post by: A.O. on January 04, 2019, 07:15:10 AM
Good job
Thanks , spent the afternoon planning down a bunch of lumber to (3/4") 1x's, got a bunk of it in the garage I'm going to use for a dresser and some shelves for our master closet. need to get it all 4 squared so I can use it... and I need it done by Sunday, its supposed to be nice and I need to have room to get the Harley out! ;-)